dein pir sensor tasmota

20200117· binary_sensor: platform: mqtt name: "pir sensor 2" state_topic: "stat/pir_sensor2/POWER" payload_on: "ON" payload_off: "OFF" device_class: motion I have two questions: on movement the device wakes up with power off and blast the “55AA000000010101” message, then it goes back to sleep after 2 minutes.

20210501· The problem is that Tasmota sends two sensor values during discovery, in later stage the FW detects that there is only one sensor so it stops sending values for the 2nd one. This is why emontnemery wrote above that it is a workaround. It is only prevent exceptions, the correct way to fix it is in the Tasmota FW. emontnemery mentioned this issue May 11, 2021. Delay HA discovery during …

20190305· I flashed the PIRSensor / NX4469675 [1] from pearl using tuyaconvert. I tried different settings/ templates I found for other PIRs, but they aren''t working: Template: Sonoff Basic, GPIO14 Sensor > Switch2 or Switch 4. Template: Generic, GPIO14 Sensor > Switch2 or Switch4. In the console, I cannot see a reaction when the PIR ...

Tasmota Motion Sensor in Home Assistant Using Tasmota Integration The definitive (?) guide to setting up a PIR in Tasmota and adding it to Home Assistant using a Tasmota integration discovery. No editing required! blakadder 28 Dec 2020. Lanbon L8 LCD Touch Switch Review Smart switch with a view! blakadder 08 Dec 2020. Sonoff B02 LED Bulb Review New Sonoff bulbs! Are they.

20210419· Whilst going to Tasmota (from Shelly) firmware allowed the device to auto recover/reboot without me needing to reset the circuit breaker there was some strange behavior happening.. ghost switching and MQTT and retain.. which was resolved by using SetOption19 1 and having Home Assistant discover and manage the device. As well as a motion sensor to trigger the light, I wanted the physical …

I connected a PIR sensor to GPIO14 of my Sonoff. it all works fine in HA. Is it possible to separate the PIR and the relay as two separate devices in HA? This way I can operate my lamp with one Sonoff and I do not have the click sound of the relay all the time if someone moves and the light is already on. This is my configuration in HA: light: platform: mqtt_json name: “SN1 LED” state ...

20190930· PIR Sensor with Wemos D1 Mini and Tasmota. I ordered a couple of these AM312 PIR sensors from Banggood recently, to test using them in a multifunction sensor with Tasmota. There is some good information on configuring Tasmota with …

The "sensor mode only" (without the chirp function) is the preferred sensor variant for Tasmota. It provides additional temperature readings. Chirp! is a plant watering alarm which uses capacitive sensing to measure moisture. It provides ambient light readings and works in Tasmota, but is not the recommended version.

PIR Motion Sensors. PIR motion sensors, albeit called sensors, are configured as switches in Tasmota since they basically report motion (1) or no motion (0) to the device. Most PIR''s are single wire and they require connecting to VCC, GND and one GPIO. In this guide we will use GPIO13 as the pin that the PIR output is connected to. See PIN Restrictions on which pins not to use. Tasmota ...

20190305· I flashed the PIRSensor / NX4469675 [1] from pearl using tuyaconvert. I tried different settings/ templates I found for other PIRs, but they aren''t working: Template: Sonoff Basic, GPIO14 Sensor > Switch2 or Switch 4. Template: Generic, GPIO14 Sensor > Switch2 or Switch4. In the console, I cannot see a reaction when the PIR ...

It’s working for the battery powered devices, both door/window and PIR sensors (needs to declare the device as such). zacnut (zac) January 18, 2020, 12:37am 17 …

A PIR sensor is really just a switch. It’s either on or off. It turns on when there’s motion, then quickly back off again, then back on briefly if there’s still motion. It doesn’t stay in the on position when it detects motion. Since it acts like a switch we select “switch” as the device type in Tasmota. If you already have a switch (like a touch module) as Switch1 then make the ...

If PIR is active, it raises the out pin to ~3V and the transistor is switched on. The LED lights and GPIO14 will be switched LOW. Regardless os SwitchMode is set to 1 or 2, the sonoff sends MQTT /cmnd/switch02/POWER2 OFF for this LOW input on GPIO14. For the sonoff tasmota I configured "GPIO14 sensor" to "10 switch2".

Sensor Configuration RTurala/SonoffTasmota Wiki. The software allows for dynamically configuration of sensors and devices to selected GPIO pins. Depending on the type of (Sonoff) Module certain GPIO pins are easily accessable. Sensor configuration is possible by either the web pages OR using the commands modules, module, gpios and gpio.

20201228· All information applies only to Home Assistant and Tasmota + You’ve connected a PIR sensor to your device and gone through instructions to set it up. Now you’re left with custom topics and grappling with Home Assistant’s and even after all that it doesn’t show up under the Device card in Home Assistant and you want the nifty Device triggers to use in ...

20180620· I bought a couple of PIR AM312 motion sensors thinking that I would easily be able to add them to my Sonoff Basic but couldn''t find this sensor in the list of available for GPIO14 and there is nothing in the wiki about it. The goal was to attach them to the Sonoff''s inside light switches so they can turn the lights on or off based on motion level.

20190522· Hi Guys. I have a sonoff basic with Tasmota firmware. I have a PIR connected to GPIO3 (can use 14 if need be) I do not want to use PIR to trigger the sonoff relay. I am only using Sonoff as means of using MQTT to be able to set some automatons using MQTT and or Service calls. So when the motion sensor triggers, I would like it to send a message to turn a hue light on, in daughter’s bedroom ...

20190512· If I was to add another PIR sensor, door sensor, or a button to this RF bridge. Well, I do not add anything to tasmota. The device is listening on RF 433MHz for any device, and I want to filter for messages that are relevant to me. Each sensor device will have a different value in Data, to identify it.

20200405· In this video I well show you hows to use and setup a 1309 lcd i2c screen with Tasmota and Esphome. I upload the Tasmota bin to my git hub and the the yaml f...

20170811· So, now when your PIR sensor turns on the Tasmota firmware will send out an MQTT message with the payload “ON”, when it turns off it will send out a message with the payload “OFF” as seen below. 23:33:14 MQTT: cmnd/sonoff7/POWER4 = ON 23:33:16 MQTT: cmnd/sonoff7/POWER4 = OFF. The MQTT topic reads: cmnd/(your device name)/POWER(the switch number you picked) Now, …